semiconductor technical data 1 rev 3 ? motorola, inc. 1997 1/97
the mc12025 is a dual modulus prescaler which divides by 64 and 65. supply voltages of 4.75 to 5.25v may be connected to pin 8. ? 520mhz toggle frequency ? lowpower 9.5ma typical ? control input is compatible with standard cmos and ttl ? operating supply voltage of 5.0v 0.25v ? propagation delay 30ns typical maximum ratings symbol characteristic range unit v cc power supply voltage, pin 8 0.5 to 7.0 vdc t a operating temperature range 40 to +85 c t stg storage temperature range 65 to +175 c electrical characteristics (v cc = 4.75 to 5.25v; t a = 40 to +85 c) symbol characteristic min typ max unit f max f min toggle frequency (sine wave input) 520 30 mhz i cc supply current 9.5 13.5 ma v ih control input high ( 64) 2.0 v v ih control input low ( 65) 0.8 v v out output voltage 0.8 1.2 v pp v in input voltage sensitivity 30mhz 100520mhz 400 100 800 800 mv pp t pll pll response time 1 t out 42 2 ns 1. t pll = the period of time the pll has from the rising output transition to the modulus control input edge transition to ensure proper modulus selection 2. t out = period of output waveform 3 4 5 6 n / n+1 0.001 m f 0.001 m f signal input modulus control input 1 v cc 8 output gnd prescaler block diagram pinout: 8lead plastic (top view) 8 1 v cc mc 7 2 nc nc 6 3 input out 5 4 input gnd mecl pll components 64/65 dual modulus prescaler p suffix 8lead plastic package case 62605 d suffix 8lead plastic soic package case 75105
mc12025 motorola hipercomm br1334 e rev 4 2 outline dimensions p suffix plastic package case 62605 issue k d suffix plastic soic package case 75105 issue r seating plane 1 4 5 8 a 0.25 m cb ss 0.25 m b m h c x 45 l dim min max millimeters a 1.35 1.75 a1 0.10 0.25 b 0.35 0.49 c 0.18 0.25 d 4.80 5.00 e 1.27 bsc e 3.80 4.00 h 5.80 6.20 h 0 7 l 0.40 1.25 0.25 0.50 notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. dimensions are in millimeters. 3. dimension d and e do not include mold protrusion. 4. maximum mold protrusion 0.15 per side. 5. dimension b does not include mold protrusion. allowable dambar protrusion shall be 0.127 total in excess of the b dimension at maximum material condition. d e h a b e b a1 c a 0.10 notes: 1. dimension l to center of lead when formed parallel. 2. package contour optional (round or square corners). 3. dimensioning and tolerancing per ansi y14.5m, 1982. 14 5 8 f note 2 a b t seating plane h j g d k n c l m m a m 0.13 (0.005) b m t dim min max min max inches millimeters a 9.40 10.16 0.370 0.400 b 6.10 6.60 0.240 0.260 c 3.94 4.45 0.155 0.175 d 0.38 0.51 0.015 0.020 f 1.02 1.78 0.040 0.070 g 2.54 bsc 0.100 bsc h 0.76 1.27 0.030 0.050 j 0.20 0.30 0.008 0.012 k 2.92 3.43 0.115 0.135 l 7.62 bsc 0.300 bsc m 10 10 n 0.76 1.01 0.030 0.040 motorola reserves the right to make changes without further notice to any products herein. motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. atypicalo parameters which may be provided in motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. motorola does not convey any license under its patent rights nor the rights of others. motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the motorola product could create a situation where personal injury or death may occur. should buyer purchase or use motorola products for any such unintended or unauthorized application, buyer shall indemnify and hold motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that motorola was negligent regarding the design or manufacture of the part. motorola and are registered trademarks of motorola, inc. motorola, inc. is an equal opportunity/affirmative action employer. how to reach us: usa / europe / locations not listed : motorola literature distribution; japan : nippon motorola ltd.; tatsumispdjldc, 6f seibubutsuryucenter, p.o. box 5405; denver, colorado 80217. 3036752140 or 18004412447 3142 tatsumi kotoku, tokyo 135, japan. 81335218315 mfax ? : rmfax0@email.sps.mot.com touchtone 6 022446609 asia / pacific : motorola semiconductors h.k. ltd.; 8b tai ping industrial park, internet : http://designnet.com 51 ting kok r oad, tai po, n.t., hong kong. 85226629298 mc12025/d ?
|
